2026-11-21
Two of the most-used probes in IEC 61032 are also the two that get confused most often. Test probe 11 is a 12 mm rod with a 50 mm stop face; test probe 12 is a 4 mm rod with a 25 mm stop face. Both are unjointed. Both are described as probes for "verifying that hazardous live parts are not accessible". They are not interchangeable, and using the wrong one gives an answer to a question nobody asked.
The dimensions are not arbitrary. Test probe 11, at 12 mm diameter with a 50 mm stop face, models a finger — specifically the finger of an adult, without the joint of test probe B. The absence of a joint is the point: probe B can bend at the joint to reach around a barrier, while probe 11 cannot. Probe 11 answers a narrower question: can a straight finger reach the live part through this opening, entering to a depth limited by the 50 mm stop face?
Test probe 12, at 4 mm diameter and 50 mm length with a 25 mm stop face, models something thinner than a finger — a tool, a wire, a thin metal strip. The 25 mm stop face exists for the same reason as probe 11's 50 mm face: to fix the insertion depth so the test is repeatable.
The practical consequence is direct. An opening of 6 mm will admit probe 12 but not probe 11. An opening of 14 mm admits both. A test that uses probe 12 on a 14 mm opening is testing whether a wire can reach the part, not whether a finger can — and those are different requirements in almost every product standard.
The probe is only half of the test. The other half is the force applied, and it differs by standard.
| Context | Applied force | Reference |
|---|---|---|
| Enclosure ingress protection, IP2X | 10 N | IEC 60529 |
| Household appliances, accessibility | 30 N | IEC 60335-1 |
| Plugs and socket outlets, accessibility | 30 N | IEC 60884-1 |
There is no 20 N step in the base standards. If a work instruction quotes 20 N, it is either a product-committee deviation or a transcription error, and it is worth checking before the test is run. A probe pushed at 30 N where the standard calls for 10 N will deform flexible barriers and produce a fail that would not occur in a correctly performed test.
Using probe 11 where probe B is required. Probe B is jointed and can articulate 90° in one plane; probe 11 cannot. On an enclosure with a recess that requires the finger to bend, probe 11 will report "not accessible" while probe B reaches the part. The test needs the jointed probe, and the report needs to say which one was used.
Applying force through the stop face. The force is applied along the axis of the probe, and the reading is taken at the point where the stop face contacts the enclosure. Pushing at an angle, or pushing until the stop face deforms, changes both the depth and the direction. A simple axial guide — a tube, or even a marked line on the probe shaft — removes most of this variation.
Ignoring the 50 mm and 25 mm depths. The stop faces are not handles. Probe 11 stops at 50 mm and probe 12 at 25 mm measured from the tip. A probe that is allowed to go deeper than its stop face is no longer a standard test, because the depth is part of the definition.
A test record that says "probe 11, not accessible" is worth very little six months later. A record that says "probe 11 per IEC 61032 figure 7, 10 N axial, stop face in contact, opening 9 mm high by 30 mm wide, not accessible" can be repeated by anyone and defended in an audit. The extra thirty seconds of writing is the difference between a test and an opinion.
Both probes are simple tools with no moving parts, which makes them easy to trust and easy to neglect. The dimensions that make them standards-compliant are also the dimensions that wear: the 12 mm and 4 mm diameters, the tip radius, and the flatness of the stop faces. A yearly check with a micrometer on the rod and a straight edge on the stop face catches almost everything that goes wrong.
Contact: Eason Wang
Phone: +86-13751010017
Tel: +86-755-33168386
Add: 1F Junfeng Building, Gongle, Xixiang, Baoan District, Shenzhen, Guangdong, China